■ Revolutionary 90 degree motherboard mounting from RAVEN RV01

■ Three 180mm Air Penetrator fans for unprecedented positive pressure and stack effect cooling

■ Supports liquid cooling radiator mounting

■ Motherboard back plate opening behind CPU area for quick cooler assembly

■ Supports 11” wide ATX motherboard

■ Highly flexible drive storage options with hot-swappable SATA adapter



Model No. SST-RV02B-E (black)
SST-RV02B-EW (black + window)
SST-RV02B-EW-USB3.0 (black + window)
Material reinforced plastic outer shell, 0.8mm Steel body.
Motherboard SSI-CEB, ATX (maximum 12” x 11”) , Micro-ATX
Drive bay External 5.25" x 5
Internal 3.5"/2.5" x 5, 2.5" x 1
Cooling system Front --
Rear --
Side --
Top 1 x 120mm exhaust fan, 950rpm, 18dBA
Bottom 3 x 180mm intake fan 700/1200rpm, 18/34dBA
Internal --
Radiator support Front N/A
Rear N/A
Top 120mm x 1
Bottom 120mm x 3
Expansion slot 7
Front I/O port USB 2.0 x 2 (SST-RV02B-E, SST-RV02B-EW only)
USB 3.0 x 2 (SST-RV02B-EW-USB3.0 only)
audio x 1
MIC x 1
Power supply 1 x optional standard PS2(ATX)
Expansion card Compatible up to 12.2" (309mm) long, width restriction-6.85" (173mm)
Limitation of CPU cooler 169mm
Limitation of PSU Unlimited
Net weight 12.6kg (RV02B-E)
12.4kg (RV02B-E-W)
Dimension 212mm (W) x 503mm (H) x 643mm (D), 68.6 liters
8.35" (W) x 19.8" (H) x 25.31" (D), 68.6 liters
Extra One CP05 included for single hot-swappable SATA hard drive, additional CP05 can be purchased separately


  • Q&A

Describe Ver Size Download
RV02-E Manual v1.0 12,287 KB
RV02-E High resolution photos 11,727 KB
RV02-E eDM (EN-RV02-E-USB3.0.pdf)   727 KB

CP05-SAS Convenient hot-swap SAS / SATA 6G connector. more...
CP07 SATA II cable are perfect for any regular SATA devices. more...
FP55 Use FP55 to support one 3.5" and two 2.5" devices in a 5.25" drive bay. more...
FP58 5.25” drive bay for slot-loading slim optical drive and four 2.5” drives more...
AP182 Equip your SG09 with AP182 for crazy airflow. more...
AR07 Highly advanced heatsink with Heat-pipe Direct Contact (HDC) technology more...
FS305-12G Three 5.25" device bay to five 3.5" SAS-12G / SATA-6Gbit/s trayless hot-swap cage more...
TD03-SLIM Super slim all-in-one liquid cooler more...
ST1200-PT The perfect balance of performance, efficiency, and quality more...
There are two main types of heat pipes used in popular aftermarket coolers, they are groove and powder. Groove heat pipes are very susceptible to gravity while powder heat pipes are less so. To achieve best performance in either heat pipe technology, they need to be placed horizontally or have the heat source side located below the other end of the heat pipe. We recommend choosing and installing components with heat pipes carefully by taking into consideration of the following examples:


The orientation of an enthusiast motherboard in a normal ATX case

The orientation of an enthusiast motherboard in the RV02-E

As the illustrations above show, most enthusiast motherboards with heat pipes will work fine in the RV02-E, the heat source is located below other parts of the heat pipe.
CPU cooler:
Horizontal style cooler

Good orientation Good orientation Bad orientation

Many CPU coolers can be rotated when installing on motherboards, the illustration here shows a SilverStone NT06-E

VGA cooler

The illustration here shows a VGA cooler that will not work well in the RV02-E because the heat source side (touching the GPU) ends up being located higher than the other end.

1. Use both hands to remove top cover gently.

2. After loosening four screws, detach both side panels gently.

3. After loosening six screws behind the front panel, detach front panel gently.

4. First, loosen two screws located on the top-front cover.
    Then push top-front cover in the direction as shown gently and finally pull up to detach the top-front cover.

5. Flip top-front cover over to loosen two screws near front I/O module and detach it gently.

6. Install USB 3.0 front I/O module (part number: G11303260) and fasten two screws back gently.

7. Assemble parts back in reverse order carefully.
    Your case is now USB3 ready.