■ Rivoluzionario il montaggio scheda madre a 90 gradi, proveniente dal RAVEN RV01
■ Frame Unibody in alluminio da 4.5mm
■ Tre ventole da 180mm per un’ineguagliabile pressione positiva ed effetto camino
■ Supporta il montaggio di radiatori per liquid cooling
■ Supporto scheda madre aperto nella zona CPU per facilitare il montaggio dei dissipatori
■ Supporta schede madri ATX larghe 11”
■ Interno fornito di pad fonoassorbenti
■
Modello nr. |
SST-FT02B (nero), SST-FT02B-USB3.0 (nero) SST-FT02S (argento), SST-FT02S-USB3.0 (argento) SST-FT02B-W (nero+ finestra), SST-FT02B-W-USB3.0 (nero+ finestra) SST-FT02S-W (argento+ finestra), SST-FT02S-W-USB3.0 (argento+ finestra) |
|
Materiale | Frame Unibody in alluminio da 4.5mm, Corpo in acciaio da 0,8mm | |
Scheda madre | SSI-CEB, ATX (Massimo 12” x 11”), Micro-ATX | |
Alloggiamento | Esterno | 5.25" x 5 |
-- | ||
Interno | 3.5"/2.5" x 5 , 2.5” x1 | |
Sistema di raffreddamento | Frontale | -- |
Posteriore | -- | |
Laterale | -- | |
Superiore | 1 x 120mm exhaust, 1200rpm, 19dBA | |
Inferiore | 3 x 180mm intake fan 700/1200rpm, 18/34dBA | |
Interno | -- | |
Supporto radiatore | Frontale | N/A |
Posteriore | N/A | |
Superiore | 120mm x 1 | |
Inferiore | 120mm x 3 | |
Slot d | 7 | |
porte frontali d'entrata/uscita | USB 2.0 x 2(SST-FT02B, SST-FT02S, SST-FT02B-W, SST-FT02S-W only) USB 3.0 x 2(SST-FT02B-USB3.0, SST-FT02S-USB3.0, SST-FT02B-W-USB3.0, SST-FT02S-W-USB3.0 only) Audio x 1 MIC x 1 |
|
Alimentatore | 1 x optional standard PS2(ATX) | |
Card grafiche | Supporta schede grafiche da 12" (304mm) o 12,2" (309mm) (con la griglia della ventola rimossa), Limitazione della larghezza- 6,69" (169mm) | |
Limite del dissipatore della CPU | 165mm | |
Limitazione di PSU | Unlimited | |
Peso netto | 15.3kg (FT02B,FT02S) 15kg (FT02B-W, FT02S-W) |
|
Dimensioni | 212mm (W) x 497mm (H) x 616mm (D), 64.9 litri | |
Extra | Un CP05 incluso con l’ hard drive SATA hot-swapp, e un CP05 supplementare possono essere acquistati separatamente |
![]() |
Describe | Ver | Taglia | Download |
![]() |
v1.0 | 7,146 KB | ![]() |
![]() |
60,225 KB | ![]() |
|
![]() |
631 KB |
![]() |
|
|
As the illustrations above show, most enthusiast motherboards with heat pipes will work fine in the FT02, the heat source is located below other parts of the heat pipe.
CPU cooler:
Horizontal style cooler
Good orientation
Good orientation
Bad orientation
VGA cooler
The illustration here shows a VGA cooler that will not work well in the FT02 because the heat source side (touching the GPU) ends up being located higher than the other end.
1. Use both hands to remove top cover gently.
2. First, loosen two screws located on the top-front cover.
Then push top-front cover in the direction as shown gently and finally pull up to detach the top-front cover.
3. Flip top-front cover over to loosen two screws near front I/O module and detach it gently.
4. Install USB 3.0 front I/O module (part number: G11303260) and fasten two screws back gently.
5. Assemble parts back in reverse order carefully.
Your case is now USB3 ready.