FP35

■ Passt in jeden 3.5’’ Einschub

■ Voll Unterstützung des SDHC Kartenformats

■ Zusätzliche Anschlüsse für USB, Firewire, eSATA und HD-Audio (Azalia)

■ Unterstützt USB 2.0 (480Mbits) für maximale Übertragungsgeschwindigkeit

■ +12V/+5V Gleichstrom Durchleitung für den Betrieb eines externen 3.5’’ Laufwerksgehäuses ohne extra Netzteil*

Hinweis

* Ein entsprechendes Stromkabel liegt bei und kann für +12V 6.4mm, mini 6Din und mini 4Din Anschlüsse benutzt werden.

 

Spezifikationen

Modell Nr. SST-FP35B
Gehäusematerial SECC
Farbe Black with extra silver front panel
Abmessungen 101.6mm (W) x 25.4mm (H) x 140mm (D)
Frontanschlüsse 1 x USB, 1 x 1394, 1 x audio (Azalia), 1 x eSATA, 1 x MIC (Azalia) ,1 x +12V/+5V pass through output
Anschluss USB 2.0 (480Mbps)
Media card power requirement USB powered
Media Card Unterstützung XD / CF I / CF II / MD /CF-Ultra II / CF Extreme /Micro Drive /UDMA CF / SD / SDHC / MMC / MMC II / MMC 4.0 /MMC Micro(w/ adapter*)/ RS MMC / HS MMC / Mini SD(w/ adapter*) / SD-Ultra II / T-Flash(w/ adapter*) / Micro SD(w/ adapter*)/ MS / MS PRO / MS Duo / MS PRO Duo(MG) / MS PRO(MG) / MS(MG) / HS MS PRO(MG) / HS MS PRO DUO(MG) / MS PRO Ultra II / Memory Stick Micro ( M2 ) (w/ adapter*)
Unterstützte Betriebssysteme Windows 98, Me, 2000, XP, Vista, Mac OS 9.x / X , Windows 7
Gewicht 390 g
Hinweis :
  *Windows 98/me requires driver installation(downloadable from download section)
 
  • Downloads
  • Empfehlungen
  • Testberichte
  • F & A


Describe
Ver
Größe
Download
FP35 Manual v1.0 2,111 KB
Driver for Windows 98/me v1.0 2,625 KB
FP35 High resolution photos 332 KB
FP35 eDM (DE-FP35B100dpi.jpg)   364 KB

CW03
Premium standard ATX HTPC chassis mehr...
TJ10
Flagship-level extended ATX tower chassis mehr...
Before you turn on the PC please make sure the power connector from your system hard drive is isolated from the power connector connected to the hard drive you wish to hot-swap. Both connectors should be on different cables from the power supply.
  1. This is the correct IDE/SATA power connector configuration. Please refer the picture as shown. (A is your system hard drive, B is your hot-swap hard drive)
  2. This is the incorrect IDE/SATA power connector configuration where both drives are being powered by the same cable from the power supply.
This configuration affects all products with hot-swappable features including: KL series, FT series, RV series, and FP35.
  1. When you are finished using your media cards (SD, CF, MS and SM etc), simply pull them out from the FP34/FP35.



  2. Please don’t use the “safely remove hardware” command as you do with normal USB devices. If you use the “safely remove hardware” command from the system tray icon, the FP34/FP35 card reader function will be disabled until you restart your system.

  1. When you are finished using your media cards (SD, CF, MS and SM etc), simply pull them out from the FP34/FP35.



  2. Please don’t use the “safely remove hardware” command as you do with normal USB devices. If you use the “safely remove hardware” command from the system tray icon, the FP34/FP35 card reader function will be disabled until you restart your system.