FSR202
￭ Fits two 2.5" SATA 6 Gbit/s drives in one 5.25" drive bay
￭ Individual metal key lock for each drive for extra security
￭ Configurable RAID 0 and RAID 1 modes
￭ Friendly LCD display with LED indicators for system monitoring during operation at all times
￭ Independent drive status LED
￭ Built-in cooling fan for excellent heat dissipation
￭ Compatible with all 2.5" drives up to 15mm thickness
￭ Fully supports SATA Hot-Swap function
SPECIFICATIONS
| Model No. | SST-FSR202 |
| Color | Black |
| Material | SGCC |
| Cooling system | 40mm low noise fan |
| Form factor | 5.25" drive bay x 1 |
| RAID function | RAID 0 / RAID 1 |
| Controller | ASMedia 1092R |
| Electrical and Operating Requirements | Line Voltage: 12V / 5V DC Maximum Power Consumption: 30W Operating Temperature: 10°C ~ 35°C (50°F ~ 95°F) Storage Temperature: -20°C ~ 47°C (-4°F ~ 116°F) Relative Humidity: 5% ~ 95% non-condensing |
| Drive support | 2 x 2.5" SATA HDD or SSD (Support up to 15mm) |
| Transfer rate | Up to 6 Gbit/s (dependent on drive speed) |
| LED indicator | Solid Purple: Fan Failure, Overheat (≥50°C), HDD Failure Solid Blue: Power, Read / Write, Rebuild Solid Red: Buzzer On |
| System monitoring | Fan Failure, Overheat, HDD / SSD Failure |
| Operating system support | Microsoft Windows 7 (32bit/64bit), 8/8.1/10 (32bit/64bit) or future release version Mac OS 10.5 or above |
| Drive interface support | SATA I / II / III |
| Net weight | 920g |
| Dimension | 148mm (W) x 43mm (H) x 140mm (D) 5.83" (W) x 1.69" (H) x 5.51" (D) |
 |
PICTURES
- DOWNLOADS
- RECOMMENDATIONS
- PRODUCT REVIEWS
- Q&A
| Describe | Ver | Size | Download |
 FSR202 manual |
V1.0 | 1,220 KB |  |
| FSR202 High resolution photos |
5,927 KB | |
|
| FSR202 GUI software |
V1.0 | 787 KB | |
|
FSR202 eDM (fsr202-edm-en.pdf)
|
165 KB |
|
|
|
1. After installing FSR202, we are unable to start the computer or the computer doesn’t recognize FSR202.
1. Please check FSR202 LCD is displaying normally.
2. Please check if the SATA cable is properly connected to the computer and whether hard drives are functioning properly.
3. If all devices function properly but computer still fail to start, there may be compatibility problem. If such incompatibility takes place, please contact our support at support@silverstonetek.com
2. Please check if the SATA cable is properly connected to the computer and whether hard drives are functioning properly.
3. If all devices function properly but computer still fail to start, there may be compatibility problem. If such incompatibility takes place, please contact our support at support@silverstonetek.com
2. Computer works fine, but FSR202 doesn’t perform correctly in reading / writing data.
Please check to see if FSR202 is currently in the process of auto rebuilding.
If it is, please wait for rebuilding to finish for full performance. If not, then please follow the below instruction to find out possible root causes:
1. Examine if connected SATA cables are too long or outside of standard spec. for connector type and quality.
2. If cables are within standard, please turn off the computer, remove both hard drives from FSR202 and connect them directly to computer to check if they read / write data normally.
Bad sectors on hard drive will affect performance and prevent proper reading / writing of data.
If it is, please wait for rebuilding to finish for full performance. If not, then please follow the below instruction to find out possible root causes:
1. Examine if connected SATA cables are too long or outside of standard spec. for connector type and quality.
2. If cables are within standard, please turn off the computer, remove both hard drives from FSR202 and connect them directly to computer to check if they read / write data normally.
Bad sectors on hard drive will affect performance and prevent proper reading / writing of data.
3. Under the Mirror mode (RAID 1), what will be the total storage capacity when adding a brand new hard drive?
1. Total storage capacity is determined by the storage capacity of the primary hard drive configured during initial RAID setup.
2. Storage capacity will not increase even if you replace one of the drives with a larger capacity model.
2. Storage capacity will not increase even if you replace one of the drives with a larger capacity model.
4. Why does error message appear when I installed a second hard drive?
The storage capacity of the new replaced hard drive must be equal or larger than the primary hard drive. Otherwise, FSR202 is unable to perform rebuilding work.
5. What will happen if we turn off the computer while FSR202 is still executing auto rebuilding?
In Mirror mode (RAID 1), if computer powers off during rebuilding, FSR202 will remember the progress of its rebuild and resume rebuilding where it left off when computer is turned on again.
6. Is it possible to lose data during auto rebuilding?
The rebuilding process automatically duplicate data from one sector to another sector.
Technically there should be no data lost during rebuilding. However, if the primary (source) hard drive has bad sectors, the FSR202 will still simulate and copy
those sectors onto the secondary (target) hard drive. Therefore, the same corrupted data is also duplicated and you may lose data this way.
7. What should I do if RAID 1 error occurs and display shows "Double Source"?
1. Determine which hard drive you wish to use as a source (primary) drive and a target (secondary) drive by removing them individually to check their content and data.
2. Turn off the computer and remove both hard drives.
3. After turning on the computer, insert the source drive into FSR202 first, then insert the target drive second. The FSR202 will then start rebuilding its RAID array.
2. Turn off the computer and remove both hard drives.
3. After turning on the computer, insert the source drive into FSR202 first, then insert the target drive second. The FSR202 will then start rebuilding its RAID array.
8. How do I make the drive I just pulled out become the source drive?
1. Turn off the computer.
2. Insert the drive you wish to use as the source drive into the FSR202, then pull out the other drive.
3. After turning on the computer, the only drive in the FSR202 will be automatically set up as a source drive.
2. Insert the drive you wish to use as the source drive into the FSR202, then pull out the other drive.
3. After turning on the computer, the only drive in the FSR202 will be automatically set up as a source drive.
9. How to change FSR202’s RAID mode?
- Turn off computer first then install 2.5" drives into the FSR202.
- Hold down ▲button then turn computer on. After five seconds, FSR202’s screen will display RAID mode switch interface.
- Press ENT button and restart computer to complete RAID mode change.