Fortressシリーズ     FT01



■ フラッグシップ級Temjin TJ07から継承された一体成形フレーム構造

■ 優れた人間工学に基づく美観かつシックなデザイン

■ デュアル180mm静音ファン内蔵で優れた冷却性能と静音性を実現

■ リベット使用を極力抑えた、メンテナンスが容易な設計

■ ホットスワップ対応SATAアダプタ装備で高い柔軟性のドライブストレージオプション

         世界初の一体成形PCケースであるSilverStone Temjin TJ07の発表から2年以上を経た今、このユニークな構造を別の範囲に応用した新たな製品が開発されました。このラインアップの初の製品となるFortress FT01は、先行モデルと同じ非常に堅牢な一体成形フレームを採用すると同時に、より小型化されたコンパクトサイズとなっています。素早く取り外せるドライブケージやデュアル180mmファンなど現代のニーズに合わせた構成の当ケースは、中型の本体構成を望む全てのユーザー皆様にとって最善の選択となるでしょう。




備考
For more information about positive air pressure,
please refer to : what is positive air pressure
   
 
  FT01 can support 10.5” consumer level graphics cards.
The support for this type of cards does not require HDD cage to be removed.
    FT01 can support 12” workstation level graphics cards.
To support such long cards, the middle HDD cage must to be removed.
 

Graphic card length reference:
NVIDIA Quadro FX5600 / AMD FireGL V8600/8650 - 12"
NVIDIA GeForce GTX280/260 - 10.5“
NVIDIA GeForce 9800GTX/9800GTX+ - 10.5“
AMD Radeon HD 4870X2 - 10.5 "
NVIDIA GeForce 9800GT/9600GT/GTO - 9"
AMD Radeon HD 4870/4850 - 9 "
If an expansion card is longer than 10.5", the middle HDD cage needs to be removed, please refer to the Q&A section for more information.
 


型番 SST-FT01B (ブラック), SST-FT01B-USB3.0 (ブラック)
SST-FT01S (シルバー), SST-FT01S-USB3.0 (シルバー)
SST-FT01B-W (ブラック+ ウィンドウ), SST-FT01B-W-USB3.0 (ブラック+ ウィンドウ)
SST-FT01S-W (シルバー+ ウィンドウ), SST-FT01S-W-USB3.0 (シルバー+ ウィンドウ)
材質 3.0mm ~ 6.0mm一体成形アルミニウム外側フレームおよびアルミニウムボディー
マザーボード ATX, Micro-ATX
ドライブベイ 外部 5.25" x 5
--
内部 3.5" (2.5”と互換) x 7
冷却システム 前面 1 x 180mm給気ファン, 700rpm, 18dBA
背面 1 x 120mm排気ファン, 900rpm, 18dBA
サイド --
トップ 1 x 180mm給気ファン, 700rpm, 18dBA
底面 --
内部 --
拡張スロット 7
フロント I/O ポート USB 2.0 x 2 (SST-FT01B, SSTFT01S, SST-FT01B-W, SST-FT01S-W only)
USB 3.0 x 2 (SST-FT01B-USB3.0, SSTFT01S-USB3.0, SST-FT01B-W-USB3.0, SST-FT01S-W-USB3.0 only)
IEEE1394 x 1
オーディオ x 1
マイク x 1
電源 1 x オプション装備標準PS2(ATX)
グラフィックス カード 拡張12" (304mm) グラフィックスカード装着可能, 幅の制限-6.85" (173mm)
CPUクーラーの限度 170mm
PSUの限度 Unlimited
実重量 8.66kg
寸法 211 mm (W) x 496 mm (H) x 494.5 mm (D), 51.8 リットル
その他 単体のホットスワップ対応SATAハードディスクドライブ用のCP05を1台付属、追加のCP05は別途購入可能

備考
To enable SATA hot-swap function, you must have the following:

  1. Install SATA hard drive into drive holder with CP05
  2. Use motherboard or SATA card with AHCI function
  3. Enable AHCI function(please refer to your motherboard or SATA card manual)
  4. When installing OS(Windows XP SP2 or Vista), SATA drivers should be pre-loaded



CP05-SAS
Convenient hot-swap SAS / SATA 6G connector. その他...
CP07
スクラッチなしロッキング機構および180°コネクタ装備のSATA IIIケーブル その他...
FP55
Use FP55 to support one 3.5" and two 2.5" devices in a 5.25" drive bay. その他...
FP58
5.25” drive bay for slot-loading slim optical drive and four 2.5” drives その他...
AP182
Equip your SG09 with AP182 for crazy airflow. その他...
AR07
ヒートパイプ・ダイレクト・コンタクト (HDC)テクノロジー採用の高度に進化したヒートシンク その他...
HE01
Twin tower cooler for maximum cooling performance. その他...
HE02
The ultimate heatsink with flexibility in nearly all applications. その他...
 
 
Describe
Ver
Size
ダウンロード
FT01 Manual
 v1.0 
2,984 KB
     
FT01 High resolution photos
  
14,955 KB
     


FT01 eDM (JP-FT01-EDM-USB3.0.pdf)
 
562 KB

A:Please refer to the FT01 180mm fan removal guide

180mm fan removal purposes:
- Upgrade original 180mm fan or for maintenance and replacement
- To gain access to the fan filter for the top mounted 180mm fan


1.Remove two screws located on the front 180mm fan bracket

2.Remove fan bracket

3.As shown in the photo, mounting holes circled in red are for 180mm fan while ones circled in blue are for 120mm fan

4.Place the case upside-down to facilitate in the removal of the first screw holding the top fan bracket

5.The second screw of the top fan bracket can be removed from behind the motherboard tray

6.The entire fan bracket assembly including the fan filter can now be removed by pulling it toward the front of the case

A:Please refer to the hard drive bracket removal guide
Hard drive bracket removal is optional for enabling more room for extra long expansion cards or when there are less than four hard drives installed.


From the case’s right side, remove the four screws holding the top hard drive bracket assembly

2. Then pull the top hard drive bracket assembly out from the left side

3. There are four screws for the lower hard drive bracket assembly that can be removed

4. Then pull out all hard drive racks from the lower hard drive bracket

5. With the racks removed, two screws holding the lower hard drive bracket to the bottom of the case can now be accessed and removed as well

6. The lower hard drive bracket can now be pulled out

A:

Currently more advanced motherboards come with either manual or automatic fan control. Under these circumstances, when the CPU temperature is low, the motherboard can lower fan voltage output to slow the connected fans down; thereby lowering the fan noise.
The fans included in the FT01, especially the 180mm fans located on top and the front, are designed for very low noise even at full speed. The 180mm fans are rated at 700rpm maximum and have sound frequency far lower than most fans, making them practically unnoticeable in normal usage. However, due to their increased size and weight, coupled with lower maximum speed, they require higher average voltage to start than smaller fans.
If the 180mm fans in your FT01 are connected to the motherboard fan headers and are having trouble starting or spinning consistently, we recommend turning off or disabling fan voltage control (whether manual or automatic) in the motherboard BIOS options. The FT01’s highly optimized cooling performance may result in the motherboard sensing lower temperature and supplying lower fan voltage through its fan headers.

A:

  1. Please unscrew the screws in the back panel as shown and remove both side panels.


  2. Please unscrews the screws in the side panel and take off the front bracket.


  3. Please unscrew the screws from inside the drive bay as shown.


  4. Finally you can take off the 5.25” plastic drive holder as shown.

A:Before you turn on the PC please make sure the power connector from your system hard drive is isolated from the power connector connected to the hard drive you wish to hot-swap. Both connectors should be on different cables from the power supply.

  1. This is the correct IDE/SATA power connector configuration. Please refer the picture as shown. (A is your system hard drive, B is your hot-swap hard drive)
  2. This is the incorrect IDE/SATA power connector configuration where both drives are being powered by the same cable from the power supply.
This configuration affects all products with hot-swappable features including: KL series, FT series, RV series, and FP35.

A:

Power switch and reset switch installation guide:
Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System Panel Connector” pin definition. Power switch and reset switch have no polarity, so they can be connected in any orientation.



LED connector installation guide:
Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System Panel Connector” pin definition.
White colored wires are negative while other colored wires are positive.
Power LED connector is designed as separate pins for compatibility with different motherboard specifications.

A:

1. Loosen three screws located on the left-side panel to remove it gently.
     

2. Flip the case upside down first, then use suitable screwdriver to loosen two screws near front I/O module and detach it gently.
     

3. Install USB 3.0 front I/O module (part number: G11303500) and fasten two screws back gently.
     

4. Assemble parts back in reverse order carefully.
     Your case is now USB3 ready.